X360 Blinker Module $17.95
36 Volt, Versions 2(round) or 3(square). For use in X360 and many other 36 volt scooters
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
BATTERY CHARGER SELECTION
* Look over the battery chargers we sell on this page. We sell universal use battery
chargers for nearly all scooters. All you need to know is how many 12 volt batteries
are installed in your scooter to determine the voltage of the electrical system
(two 12 volt batteries would be a 24 volt system). Most scooters use lead acid batteries, but some use Lithium or even LiP04. Chargers should match the type batteries used.
* Find a charger that matches your scooter's battery electrical system 12, 24, 36, or 48 volts
beginning at the top of the page and scrolling down until you find a charger of the correct
voltage (they are all standard AC input for 110/220 volt, with only one Euro plug charger, the rest standard American) for charging 12, 24, 36, 48, 60 volt output and the connector
mates to your scooter charge receptacle. The most common charger plug is a 3 prong female
type that mates with a three pin male receptacle, but other plugs like the PC style and XLR are also used and pictured/described.
* Note that battery charger output DC voltage is alway slightly higher than the system voltage so
that, for example, a 24 volt charger would output 29 volts in order to charge the battery set of
two 12 volt batteries connected together in series. With this information you should find a
charger that will charge your batteries and automatically turn off when finished, providing a light indication for full charge.
* Electrical components are not covered by warranty for return to exchange or for refund. Parts are tested prior to packaging for correct operational condition. If your battery stystem is not malfunctioning then the charger will operate correctly on receipt, but if your previous charger malfunctioned because of a system problem then your new charger will also fail. Many of our charger have some fuse protection inside the case to help prevent a total burn out and the fuse can be replaced.
3 prong Female Plug, 12 Volt
Battery Charger For Gas and Electric Scooters with
three prong socket Receptacles (90-245V AC with
16.5V DC 1.0A Output) $14.95
plus shipping/handling
Intelligent Battery Charger provides current to battery set at
correct amount to charge without overheating, shut off when
batteries are charged. Choice of connector.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
X-10 and X-140 24V Battery Charger, replaces old style
Battery Charger which was prone to failure and overcharged
batteries. New Intelligent X-10 and X-140 scooter battery chargers
automatically charge batteries at a rate that will not damage
batteries and shuts off to prevent overcharging or charger failure
- High Quality, same single pin connector for X-10/X-140 Scooters plus
others like Sharper Image and Izip 130 - $22.95
plus shipping/handling
3.5mm Single pin female connection to scooter charger input
port.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Battery Charger INPUT PORT - $9.95
plus shipping/handling Regular
$14.95
3.5mm Single pin male connector receptacle for x010 Battery Charger
input.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
CONNECTOR PLUG, 3.5MM - $7.95
plus shipping/handling. Regular Retail
Price less shipping $14.95
3.5mm Single pin female connector plug for x010 and other scooters
Battery Charger input.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
24 volt, 2 or 3 prong OEM Battery Charger
for the model X-11 or X-250 X-treme scooters and other models $58.95
Plus Shipping/Handling
Intelligent charger provides current to battery set at correct
amount to charge without overheating, shut off when batteries are
charged. Indicator light shows charging and when charged. WE NOW SHIP THE 24 VOLT 3 PIN CHARGER WITH THE MATCHING 3 PIN MALE SOCKET BECAUSE THE 2 PIN X-TREME OEM CHARGER IS NO LONGER AVAILABLE. The socket easily installs in place of the old 2 pin socket and still uses only 2 of the three pins.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
24 VOLT
MOST POPULAR 24 VOLT BATTERY CHARGER, 3 Prong Plug. $17.95
(90-245V AC with 29.5V DC 1.6 Amp Output)
Use with all 24 volt, 3 prong scooters with either standard female
connector or XLR Male Connector, connected and ready to use.
This charger is superior to most sold scooter chargers because it
has a fuse that can be changed if blown due to overload or short.
The case can be opened, unlike most others, and the fuse replaced.
But if your socket is different it can still be used by replacing
the socket on the scooter. Need a socket? See it available
separately.
plus shipping/handling
Charger indicates red when charging and green when fully charged.
May be used with two prong Battery Charger connectors by using the
old two prong plug from the previous Battery Charger. Only two of
the three pins are used in three prong chargers (pin 1 is always
positive).
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
24 Volt, 3 Prong Male XLR Connector -
$34.95
(100-240V AC with +24V DC 1.6 Amp Output)
plus shipping/handling
OEM 24 volt, three MALE prong
Battery Charger as used on many Scooters
including Schwinn, Mongoose, GT, and Currie. Charger with indicator
light shows when charging and fully charged. Matches socket below.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Battery Charger, Europe Plug, 24
Volt, 3 Prong Female Plug. $24.95
(90-245V AC with 29.5V DC 1.6 Amp Output)
Use with AC oulets in Europe only (
American version above). For all 24 volt, 3 prong scooters
with 3 pin male sockets. This charger is superior to most sold
scooter chargers because it has a fuse that can be changed if blown
due to overload or short. The case can be opened, unlike most
others, and the fuse replaced. But if your socket is different it
can still be used by replacing the socket on the scooter. Need a
socket? See it available separately.
plus shipping/handling
Charger indicates red when charging and green when fully charged.
May be used with two prong Battery Charger connectors by using the
old two prong plug from the previous Battery Charger. Only two of
the three pins are used in three prong chargers (pin 1 is always
positive).
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
24 VOLT
LITHIUM ION BATTERY CHARGER, 3 Prong Plug Choice. $39.95
(DC 2 Amp Output)
Use with all 24 volt, 3 prong scooters with either standard female
connector or XLR Male Connector, connected and ready to use.
This charger is made for Lithium Ion battery set charging. Fan cooled.
plus shipping/handling
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
MOST POPULAR 36 VOLT BATTERY CHARGER, 3 Prong Connector For
$19.95
(90-245V AC with 42.6V DC 1.6 Amp Output). Same charger as used on some X360 Scooters when 3 pin female connector is selected in the drop down menu.
plus shipping/handling
36 volt, three prong Battery Charger with either standard female
connector or XLR Male Connector, connected and ready to use. Charger with indicator light shows
when charging and fully charged. May be used with two prong Battery
Charger connectors by using the old two prong plug from the
previous Battery Charger. Or purchase the three prong socket below
for replacement to match this Battery Charger connector.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
36 volt X-treme's OEM (Original Equipment Manufactured) Battery Charger and Socket for the X-treme X360 and other
scooters with 2 OR 3 prong male sockets on the scooter. $64.95
Plus Shipping and Handling
Intelligent Battery Charger provides current to battery set at
correct amount to charge without overheating, shut off when
batteries are charged. Indicator light shows red during charge,
green when charged. WE NOW SHIP THE 36 VOLT 3 PIN CHARGER WITH THE MATCHING 3 PIN MALE SOCKET IN PLACE OF THE 2 PIN VERSION BECAUSE THE OEM 2 PIN CHARGER IS NO LONGER AVAILABLE. The socket easily installs in place of the old 2 pin socket and still uses only 2 of the three pins.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
36 Volt, 3 Prong Male XLR Connector -
$39.95
(100-240V AC with 41.8V DC 1.6 Amp Output)
plus shipping/handling
36 volt, three MALE prong
Battery Charger as used on many Scooters
including some X-treme Models, MX500, etc. Charger with indicator
light shows when charging and fully charged. Matches socket below.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Battery Charger Receptacle, two prong male
$16.95
for X-treme X11, X360 models and many others.
Plus shipping/handling.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
3 Prong Battery Charger Receptacle.
Replaces the 3 pin male receptacle on the Scooter $8.95
plus shipping/handling
Standard male 3 pin receptacle socket to receive the female three
pin Battery Charger plug of most Electric Scooters including Vapor
Scooters. Replacement for any make Scooter, may require splicing to
your existing wiring connectors to your control box.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
3 Prong Female Socket For $11.95
plus shipping/handling
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
3 Prong Battery Charger
Plug
Replaces the standard female or male XLR plug on the Scooter Battery Charger cord
$5.95
plus shipping/handling
Standard three pin Scooter Battery Charger plug of
most Electric Scooters including Rad2Go, Razor, Vapor and X-treme
Scooters.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
48 Volt 3 Amp Fan Cooled
Battery Charger, Choice of Panterra Polarity or Standard Polarity
PC Style Female Connectors, $79.95
plus shipping/handling
Intelligent 48 volt, three prong PC Style connector plug, Fan
Cooled, Intelligent Lead Acid Battery Charger with 100-240V AC input with 53.5V DC
output (for 48 volt battery set) and up to 3 Amps Output. Charger with two indicator lights show when
charging and fully charged. Polarity for most Pantera scooters or
standard scooter polarity.
Charger Indicator pictures for charging and charged state.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
48 Volt 2.5/3 Amp Fan Cooled
Battery Charger, Standard 3 Prong Round Connector, $79.95
plus shipping/handling
Intelligent 48 volt, three prong round connector plug
(matches the sockets on this page), Fan Cooled, Intelligent Battery
Charger with 100-240V AC with 53.5V DC 2.5 Amp Output. Charger with
two indicator lights show when charging and fully charged. If your
socket is different it can still be used by replacing the socket on
the scooter with the matching socket sold here, or by splicing or
soldering on your old charger's plug. Plug polarity is indicated on
the case of the charger as the normal Pin 1 positive. Your choice
of standard 3 pin round female connector or XLR 3 pin male connector.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
48 Volt Lithium LiPo4 Fan Cooled
OEM Battery Charger $107.95
plus shipping/handling
Intelligent 48 volt, three prong connector plug, Fan Cooled, Heavy Duty Lithium LiPo4 Battery
Charger with 100-240V AC input. Charger with
indicator lights show when charging and fully charged. Not compatible with LIMN battery sets.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
60 Volt 1.6 Amp Lead Acid Fan Cooled
Battery Charger $69.95
plus shipping/handling
Intelligent 48 volt, three prong connector plug, Fan Cooled, Heavy Duty Lead Acid Battery
Charger with 100-240V AC input. Charger with
indicator lights show when charging and fully charged. Choice of output connectors.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
60 Volt 2.5 Amp Lead Acid Fan Cooled
Battery Charger $99.95
plus shipping/handling
Intelligent 48 volt, three prong connector plug, Fan Cooled, Heavy Duty Lead Acid Battery
Charger with 100-240V AC input. Charger with
indicator lights show when charging and fully charged. Choice of output connectors.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Heavy Duty 48 Volt 9 Amp
POPULAR BATTERY CHARGER For $174.95
48V Fan Cooled Charger for large electric scooters like the
Panterra. Amperage output is up to 9 Amps. Fast charge use for
Panterra (Freedom electric), Panterra (Fusion electric), Panterra
(Retro Electric), and Various makes/models of electric scooters of
different connection polarities. Fan cooled for heavy duty use,
fuse protected. Pretested in load environment for a 48 volt battery set.
Also, a standard scooter polarity version of this same charger for many
brands of scooters using this type connector.
And we can attach a 3 prong round female connector (Pin 1 is positive) in place of the PC Style connector when you order it separately and ask us in the message area to attach the connector. No charge for labor. Order the connector above if needed.
plus shipping/handling Availability of this
item?
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
3 Prong PC Style Battery Charger Receptacle.
Replaces the male receptacle on the Scooter $7.95
plus shipping/handling
PC Style male 3 pin receptacle socket to receive the female three
pin Battery Charger PC Style plug of most Electric Scooters. Replacement for any make Scooter, may require splicing or soldering to
your existing wiring connectors to your control box.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
CONTROL BOXES - Control Boxes are rated in Wattage, Volts and Amps for different scooter system voltages, 24, 36, 48, and 60. Maximum peak watt motor usage is typically found by multiplying volts times amp rating when amps given is peak amp rating. Sustained wattage can be found by multiplying volts times run amp rating. In general when you see a wattage rating shown that is less than the product of multiplying the amps and volts it means the amps rating is the peak or maximum rating the control box can safely handle during acceleration from a stop or such loads. The normal operating amperage can be found by dividing the given wattage in this case by the voltage. YOUR BEST ADVICE IS TO BUY THE LARGEST CONTROL BOX RATING IN WATTS FOR THE SYSTEM VOLTAGE OF YOUR SCOOTER THAT PHYSICALLY WILL FIT IN THE CAVITY WHERE YOUR CONTROL BOX MOUNTS. No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
HOW TO SELECT THE BEST CONTROL BOX FOR YOUR REPLACEMENT: These control boxes were selected for maximum universal replacement of almost all scooters as quality devices. To determine the best replacement you should first consider the voltage of your scooter where the number of 12 volt batteries yields the total voltage when combined (e.g., three batteries will be 36 volts). The wattage of the motor the controller will provide power to should be determined so that, for example, a 350 watt motor would need a control box capable of at least 350 watts output or more. Controller wattage can be higher than the motor wattage and make the controller less likely to overheat or burn out. You should also consider the connectors your existing control box has to the component harnesses so that you might be able to simply plug in the new control box (e.g., if your scooter has a six pin connector for the throttle/brake lever/speed indicator then that would be preferable to a control box with separate connectors for the throttle and brake lever, but we sell a connector package to allow new connectors for the existing wiring harness). And you need to consider whether you have room for the physical size of the new control box in the area of your old control box. Connector problems can be overcome by using a replacement universal conector package we sell on this page if, it comes to that, and the connector set is not expensive with the most used types. And most scooters can accomodate a larger control box. Also, do look at the Wiring Connection diagrams and information links provided in the part descriptions, and be sure to mark your connectors on your scooter as they are used for the different components (e.g., throttle, switch/lock, brake lever, brake light, charger socket, on/off power indicator light, motor, and battery set.
NOTE: Most people do not know that control boxes limit the current to the motor to help prevent burn outs during acceleration and heavy use. This restricts the full power of the battery set from being applied to the motor, restricting the acceleration and top speed to some extent. Control boxes are designed to shut off when current reaches a maximum for the rating of the control box, and when the voltage drops to the minimum that is quoted. This again helps protect the control box. For example, if you have a 36 volt system with a control box rated at 40 amps for a 1000 watt motor and your motor pulls more than 40 amps under a full load or causes the voltage to drop below the cut-out rating of 32 volts, the control box will attempt to shut down causing the scooter to not reach full speed as the scooter bucks with the motor cutting in and out in a fluctuation. Remedy, a smaller motor or a 1000 watt motor that draws less amps under the same load. Note that load is actually the weight of the scooter, rider, and environment of use (road condition, hills, etc.). As an alternative higher loads may force the use of a 48 volt or higher voltage system to drop the amperage down through a control box to the motor. One inventive individual provided us an article on how to use a relay system to safely direct connect the battery system to the motor for brief acceleration and high speed, bypassing the control box briefly. This article is available on this site in our performance section.
X-TREME X-10 100 Watt Control Box (ver 2) - $44.95
plus shipping/handling.
No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
Wiring diagram
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Control Box For Vapor Scooter $22.95
plus shipping/handling - When Available Only Wiring diagram Pin ID Picture of Original Vapor Controller. Replacement control box using the same small pin connectors for Vapor scooters and others of the same type. Plug in and go. The Vapor may also be called Tornado and other names.
No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
OEM Control Box for X-treme X-250 $49.95
OEM (original equipment manufactured) controller for the X-treme X-250 as currently manufactured. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
30 AMP 24 VOLT CONTROLLER for Motors up to 300 WATT - $29.95
plus shipping/handling
-
Wiring connection, LB27, 300 Watt or less Scooter Replacement at 10 normal amps to 30 amps peak. 3.25"L X 2.25"W X 1.35"H. Small size for tight spot location. 20.5 volt under voltage protection extends battery life. Harness wiring supports key switch, brake indicator, power indicator, charger connector, 3 wire throttle, brake lever cutout switch cuts battery output, motor, and battery. Some wire splicing may be necessary in some applications.
Tested prior to packaging. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
30 AMP 24 VOLT CONTROLLER for Motors up to 400 WATT - $34.95
plus shipping/handling
-
Wiring connection, CT-302S9, 400 Watt or less, 10.5 normal amps to peak 30 amps. 4.25"L X 2"W X 1.4"H. Small size for tight spot location. Current limiting avoids damage to the motor and controller. Under voltage protection extends battery life. Over speed prevention while charging (renders the throttle temporarily inoperable to prevent mistaken manipulation). Harness wiring supports key switch, brake indicator, power indicator, charger connector, 6 wire for throttle/brake lever/speed indicator, motor, and battery. Some wire splicing may be necessary in some applications.
Tested prior to packaging. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
30 AMP 24 VOLT CONTROLLER for Motors up to 500 WATT - $34.95
plus shipping/handling
-
Wiring connection, CT-811B9, 7 connector, 500 Watt or less, 10.5 normal amps to peak 30 amps. 4.35"L (3.2"L not including mounting tabs) X 3"W X 1.3"H. Small size for tight spot location. Current limiting avoids damage to the motor and controller. Under voltage protection extends battery life. Over speed prevention while charging (renders the throttle temporarily inoperable to prevent mistaken manipulation). Harness wiring supports key switch, brake indicator, power indicator, charger connector, 6 wire throttle/brake lever/speed indicator (no speed wire on CT-803B9), motor, and battery. Some wire splicing may be necessary in some applications.
Tested prior to packaging. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
30 AMP 24 or 36 VOLT CONTROLLER 500 WATT - $45.95
plus shipping/handling
-
Wiring connection, JC-116, 24 or 36 Volt 500 Watt or less Scooter Replacement at 30 amps. Small size for tight spot location, 3.25L, 2.5W, 1.25H. Mounting bracket along back edge. Current limiting avoids damage to the motor and controller. Under voltage protection extends battery life. 8 connector harness wiring supports key switch, battery capacity, charger connector, 3 wire throttle (this is one of the few 36 volt controllers with a three pin connector for the throttle), brake lever cutout switch cuts battery output, stop light, motor, and battery. Some wire splicing may be necessary in some applications.
Tested prior to packaging. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
30 AMP 24 VOLT CONTROLLER for Motors up to 750 WATT - $44.95
plus shipping/handling
- Wiring connection, LBD14, 750 Watt or less, 10.5 normal amps to peak 30 amps. 3.5"L X 2.75"W X 1.5"H. Small size for tight spot location. Seven connectors. Current limiting avoids damage to the motor and controller. Under voltage protection extends battery life. Over speed prevention while charging (renders the throttle temporarily inoperable to prevent mistaken manipulation). 8 wire harness supports key switch, brake signal, power indicator, charger connector, 3 wire throttle, brake lever cutout switch cuts battery output, motor, and battery. Some wire splicing may be necessary in some applications.
Tested prior to packaging. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
500-950 WATT 24 or 36 VOLT 30 AMP REVERSABLE CONTROLLER $64.95
plus shipping/handling This controller has 8 connects. Rated Voltage 24 or 36 Volts. Max Current 30 Amps. Usable Motors: 500+ Watts. 4"L X 2.75"W X 1.5"H.
Rated Voltage: 24 or 36 Volts, Rated Motors 500+ watts, Rated Current to 30 amps, Conversion Efficiency: 95%, Under voltage protection: 20.5 volts or 31, Speed control: Hall effect Turn or thumb throttle, Brake Indicator, Power Indicator, 3 Wire Lock/Switch Connector with Forward or Reverse function, Charger connector, Pilot Light connector, Brake Lever cut-out connector, Motor and Battery connectors. Possible easy mount switch assembly for use in forward and reverse control is our
handlebar mounted switch assembly or
three position key switch sold below.
Current Limiting prevents motor current from exceeding the specified value and avoids damage to the motor and control box due to over current conditions. Under voltage protection when the battery voltage falls to specified value, cutting battery output and preventing over discharge which extends battery life. Over speed prevention while charging renders the throttle temporarily inoperable and prevents mistaken operation. Power cut-off during braking.
Simple connector plugs use or splice of harness wires to existing scooter wiring from control box or to components.
Tested prior to packaging. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
Wiring Connection
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
30 AMP 600 WATT 24 VOLT HEAVY DUTY CONTROLLER - $54.95
plus shipping/handling (5L X 3.5H X 2H). YK42-2. This 30 amp controller is a replacement for electric Scooters using up to 600 watt 24 volt motors wired similar to the Rad2Go E10 Scooter. Easy splice wiring harness. Just connect to motor, 3 wire connector for hall effect throttle, and then 36 volt battery set through a switch for high quality and endurance you need.
Tested prior to packaging. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
Wiring diagram
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
20 Amp 36 Volt Control Box for X360 350-500 watt motor and other scooters $68.95
Replacement controller (brain) for 36 volt model X-360. In the X360 this control box replaces your controller when you EMAIL US INFORMATION ABOUT YOUR INSTALLED CONTROL BOX as indicated at this link that provides troubleshooting help. USE THE FOLLOWING INFORMATION TO DETERMINE THE VERSION NUMBER AND SELECT IT ON THE ORDER MENU BEFORE ADDING THE ITEM TO THE SHOPPING CART.
No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect. Lifetime technical support is available through X-treme's Support Ticket system.
VERSION 2, 3, 4 and G2 are out of production and no longer available. Other versions will work for basic operation without blinkers, stop light, horn, and some other features.
VERSION 5 Upgraded replacement controller (brain) for 36 volt model X-360. This item can also work in all other 36 volt scooters but may require modification to the wire harness. This item replaces controllers made after Mid 2005
VERSION 6 Upgraded replacement controller (brain) for 36 volt model X-360. This item can also work in all other 36 volt scooters but may require modification to the wire harness. This item replaces controllers in the X-360 scooter made August 2009.
Check your controller for Version Number and comparison to pictures provided here and elsewhere. No refunds on electrical parts. Please order the correct part the first time. No refunds due to the sensitive nature of these devices.
Wiring Connection
Wiring diagram PDF
Wiring diagram JPG
Wiring diagram Dash JPG
[NOTE: WIRING MAY BE DIFFERENT FOR THE X360 DEPENDING ON THE CONTROL BOX VERSION AND YEAR OF MAKE]
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
X-treme X-360 Version Generation 2. $68.95
The Version G2 is no longer in production and has been replaced by the Version 6. No refunds on electrical parts. Lifetime technical support is available through X-treme's Support Ticket system.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
350-500 watt 36 Volt Control Box $44.95
Replacement controller (brain) for 36 volt 350 watt motors. 4.25"L X 2"W X 1.4"H. Connectors for Battery, Motor, 6 wire connector for standard three wire throttle, brake lever, and speed control. Plus switch, charger socket, and Brake light connectors. This control box will replace many X360 control boxes, excluding lighting connections. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
Wiring Connection
Wiring diagram PDF
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
36 Volt Digital Controller 30 amps $59.95
plus shipping/handling YK31C-36 - for up to 600 watt electric motors. 6 wire connector harness supports key switch, charger connector, 3 wire throttle, brake lever cutout switch cuts battery output, motor, and battery. 4.5"L X 2.75"W X 1.5"H.
Tested prior to packaging. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
Similar Wiring Harness
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
1000 Watt 36 Volt 40 Amp Controller for up to 1000 Watt 36 Volt Motors $64.95
plus shipping/handling CT-660B9. This controller has 7 connectors. Rated Voltage 36 Volts. Max Current 40 Amps. Usable Motors: up to 1000 Watts. Diminsions: 5"L X 3"W X 1.5"H
Rated Voltage: 36 Volts, Rated Motors to 1000 watts, Rated Current to 40 amps, Conversion Efficiency: 95%, Under voltage protection: 31.5 volts, 6 wire connector for throttle/brake lever/speed indicator, Brake Light, Power Indicator, Charger Connector, Lock/Switch connector, Motor and Battery connectors.
Current Limiting prevents motor current from exceeding the specified value and avoids damage to the motor and control box due to over current conditions. Under voltage protection when the battery voltage falls to specified value, cutting battery output and preventing over discharge which extends battery life. Over speed prevention while charging renders the throttle temporarily inoperable and prevents mistaken operation. Power cut-off during braking.
Simple connector plugs use or splice of harness wires to existing scooter wiring from control box or to components.
Tested prior to packaging. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
Wiring Connection
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
1000 Watt 36 Volt 40 Amp Controller for up to 1000 Watt 36 Volt Motors $59.95
plus shipping/handling 36 Volt 1000 Watt 40 Amp. This controller is a superior upgrade heavy duty device that has 8 commonly used connectors: Power Source - black/red wires, 2-pin male,
Motor - blue/yellow wires, 2-pin female, Brake Lever - black/yellow wires, 2-pin female, Throttle (Derailler) - red/black/blue where blue and green are always interchangeable wires, 3-pin female, Brake Light - red/black wires, 2-pin female, On/Off (Lock)Switch - red/blue wires, 2-pin female, Charging Port - red/black wires, 2-pin female, Indicator - red/black wires, 2-pin female.
Simple standard installation using new controller's clearly marked and identifed connector plugs, or use controller connector set sold separately below to match your wiring harness connectors, or use existing old controller connectors by detaching the blades in the new connectors and inserting in the old molex connectors as necessary (small screwdriver or jewelers screwdriver required to remove blades).
Tested prior to packaging. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
Diminsions: 3.5"L X 2.5"W X 1.5"H
Typical Wiring Connection
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
36 Volt Digital Heavy Duty Controller for up to 40 amps and up to 1000+ Watt Motors. $69.95
plus shipping/handling A great buy on this heavy duty simple 40 amp control box for up to 1000+ watt electric 36 volt motors. Just connect to motor, 3 wire connector for hall effect throttle, Brake lever cut out switch (on some versions), and then 36 volt battery set through a switch for high quality and endurance you need. 7.5"L X 3.5"W X 2"H. For scooters with wiring similar to the Rad2Go E36 Great White Scooter. This control box has a large shared red (positive) lead to both the battery terminal AND motor, with a Blue (or Green) negative large wire to the Motor, and a heavy duty toggle switch or relay switch in the Black wire battery circuit for On/Off control.
Tested prior to packaging. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
Wiring Connection
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
48 Volt Digital Controller up to 1500+ Watt Motors at 50 amps $81.95
plus shipping/handling LB37 - for up to 1500+ watt electric motors. 7 wire connector harness supports key switch, charger connector, 3 wire throttle, brake lever cutout switch cuts battery output, power indicator light, motor, and battery. 4.5"L X 2.75"W X 1.5"H.
Tested prior to packaging. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
Wiring Connection
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
48 Volt Digital Controller 60 amps $59.95
plus shipping/handling YK31C - for up to 600 watt electric motors. 6 wire connector harness supports key switch, charger connector, 3 wire throttle, brake lever cutout switch cuts battery output, motor, and battery. 4.5"L X 2.75"W X 1.5"H.
Tested prior to packaging. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
Similar Wiring Harness
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
48 Volt Digital Heavy Duty Controller for up to 100 amps and 2000+ Watt Motors. $74.95
plus shipping/handling YK42-4 - A great buy on this heavy duty simple 40 - 100 amp control box for up to 2000+ watt electric 48 volt motors. 6"L X 3.5"W X 2"H. Just connect to motor, 3 wire connector hall effect throttle, and then 48 volt battery set for high quality and endurance you need.
Tested prior to packaging. No returns or exchanges due to the sensitive nature of this device (Buy at your own risk). Installation is suggested by a competent person using care to avoid misconnection and static electricity that will cause a defect.
Wiring Connection
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
HUB MOTOR CONTROLLERS FOR X-TREME MODELS:
XB-500 CONTROLLER, 48V 500W
XB-502 CONTROLLER, 48V 500W
XB-508 CONTROLLER, 48V 500W
XB-600 CONTROLLER, 48V 600W
XB-610 CONTROLLER, 48V 600W
XB-700 CONTROLLER, 48V 700W
These control boxes for rear hub motors may or may not be compatible with other scooter applications. Only a competent mechanic should attempt connection of any hub motor control box due to the complexity of wiring. All control boxes and electronic parts are sold without the ability for any return or exchange due to the sensitive nature of these sensitive devices to static electricity induced burn outs and unintentionally induced defects. No manufacturer will warranty any control box or accept returns or exchanges.
CONVERTER 25-75V OUTPUT TO 12V DC - $23.95
plus shipping/handling - 3-pin connection, Wire colors: Red, Yellow and Black, DC481213, DC 30V-60V to DC 12V / 10A, Measures 3 x 3 x 1 1/4"Supported Models: Various unlisted makes/models, Panterra (Freedom electric), Panterra (Fusion electric), Panterra (Retro Electric), X-Treme
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
SIX CONNECTOR SET FOR SCOOTERS - $8.95
plus shipping/handling
- Universal set of Scooter Connectors. Six male and female standard white Molex connector sets: two, three, four, six pins, 2 pin motor, and battery 2 pin connector sets. Makes installation of control boxes easier. Blades included.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
FIVE MODULAR CONNECTOR SET FOR SCOOTERS - $7.95
plus shipping/handling
- Modular black mini set of Scooter Connectors. Five male and female standard Modular connector sets: two, three, four, five, and six pin connectors in this set. Makes installation of control boxes easier especially when using control boxs with white molex connectors as replacements. Blades included.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
INLINE FUSE BLOCK WITH 30 AMP FUSE -
$16.95
plus shipping/handling -
Battery circuit protection with this inline fuse block and 30 amp
fuse
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
ADD $1 SHIPPING IF ORDER TOTAL IS LESS THAN $10
METRIC SIZE 25A FUSE - $4.95 SET OF 5
plus shipping/handling - 5 X
20mm Metric replacement fuse
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
OR
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
FUSEHOLDER FOR METRIC SIZE
FUSE - $7.95
plus shipping/handling - 5 X
20mm metric fuse holder
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
FUSEHOLDER FOR AMERICAN SIZE FUSE,
3AG - $4.95
plus shipping/handling -
Universal American size replacement
Replaces impossible to get metric fuse holder and fuse
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
FUSEHOLDER AND 25AMP FUSE, 3AG -
$6.95
plus shipping/handling. -
Universal American size replacement
Replaces impossible to get metric fuse holder and fuse
X360 Left Grip Switch Assembly (no
grip, sold below). $12.95
This grip switch comes with three
switches: A two wire on/off light switch, A two wire momentary Horn
Button, and a three wire Turn Signal switch that can also be used
to control forward and reverse control boxes, if so desired (low
current operation only such as reversable control boxes sold
above). See grip
switch normal wiring and wiring
when used with reverse control boxes.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
X360 Dash Panels.
$19.95
The dash panel words Battery and Speed are centered under the icons (A - red housing) for version 2 Headlight assemblies. Version 1 (shown B in yellow housing) has the words to the side of the icons and limited to stock on hand and cosmetic condition may vary. Clear panel section only, does not include headlight housing shown in red or yellow in the pictures. Wiring information not included. No returns or exchanges.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
X360 Version 1 Headlight Assembly.
$29.95
Available colors choices may vary: Burgandy, Blue, Yellow, Black
and Pink options. Version 1 does not have a power switch hole in
addition to the Ignition Key switch hole. Includes Headlight, turn
signal lights, and Guages. Limited Quantities, subject to availability.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
X360 Version 2 Headlight Assembly.
$29.95
Available colors choices may vary: Burgandy, Blue, Yellow, Black
and Pink options. Version 2 has a power switch hole in addition to
the Ignition Key switch hole. Includes Headlight, turn signal
lights, and Guages. The dash panel words Battery and Speed are centered under the icons (A Type).
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
X360 Headlight Lens.
$17.95
Available colors choices may vary: Burgandy, Blue, Yellow, and
Black options. Specify your desire in the message area of the
order. Otherwise we will ship as available
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
X360 Headlight Housing.
$19.95
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
X360 Headlight Speed/Battery Clear Lens.
$10.95
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
X360 Headlight Bulb.
$13.95
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Horn for X360, 36 volt $17.95
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
ADD $1 SHIPPING IF ORDER TOTAL IS LESS THAN $10
Switch for X010 and X11 $11.95
Availability of this item?
On/Off Switch for X010 $13.95
Availability of this item?
OEM Ignition Switch with key for X360 and
other scooters $29.95
X-360 scooter OEM (Original Equipment Manufacturer brand part used for assembly) switch with keys, and battery compartment latch for same keyset
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Ignition Switch with keys - $12.95
A 2 wire key switch and key set. For most electric scooters.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Ignition Switch
with keys $12.95
A 2 wire key switch for larger hole switches. Snaps in place. Vapor and similar scooters.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Kill Switch with Handlebar Grip-
$12.95
plus shipping/handling. Regular Retail
Price less shipping $15.95
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Master Switch for New Model
X360 $13.95
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Throttle Control Assembly For Most Electric Scooters $14.95
plus shipping/handling
Twist Grip Motorcycle Style Throttle and 5 feet 3
wire cable (black, green, red or black, blue, brown where red =
brown and green = blue ) for all 7/8 inch standard handlebars.
Otherwise known as a Hall Effect Throttle. Now available with three different connector choices: Box type female connector (A), Blade connector for standard white molex connector (B), or Vapor and X-10 mini connector (C). Throttle may come with trim styling.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
OR
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
OR
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
OR
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Left Grip (no switch assembly) for
standard 7/8 $4.95
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Throttle and Left Grip for
standard 7/8 $17.95
Plus Shipping and Handling
Standard three wire hall effect electric scooter throttle with red, green, and black wires to blade connectors that insert into white molex connectors. Matching left grip.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Throttle and Left Grip for
standard 7/8 $17.95
Plus Shipping and Handling
Standard three wire hall effect electric scooter throttle with red, green, and black wires to blade connectors that insert into white molex connectors. Matching left grip.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Switch Assembly For Scooters $5.95
plus shipping/handling
Engine push button starter/kill switch to which the twist throttle can attach for pocket bikes, mini choppers and scooters. The yellow button can be wired as a push button starter, kill switch or even possibly a reverse switch for mobility scooters with a simple two wire make contact function.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Thumb Throttle Control Assembly For 24 Volt Scooters $23.95
plus shipping/handling
Hall Effect Throttle Control and 5 feet 3 wire cable
harness (terminating in bare wire), Red (4.3 Volts), Green (or blue
- Speed Adjusting Signal), Black (Ground), optional 4th wire - White wire (or
Yellow to Power and Battery Status Indicator of 24 volt control box). Splice for
quick repair. May be used in any voltage system with the standard three throttle wires, red, greed, black. 7/8 inch standard handlebar mount.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Thumb Throttle Control Assembly For 36 Volt Scooters $24.95
plus shipping/handling
Hall Effect Throttle Control and 5 feet 3 wire cable
harness, Red (4.3 Volts), Green (or blue
- Speed Adjusting Signal), Black (Ground), optional 4th wire - White wire (or
Yellow to Power Indicator of 36 volt control box). Insert blades in existing white Molex connector for
quick repair. 7/8 inch standard handlebar mount.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Half Twist Throttle Control Assembly For Scooters $19.95
plus shipping/handling
Hall Effect Half Throttle Control and 3 wire cable
harness: Red (4.3 Volts), Green (Speed Adjusting Signal), Black (Ground). Insert blades in existing connector or splice for
quick repair. 7/8 inch standard handlebar mount.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Half Twist Throttle Control Assembly For Scooters $19.95
plus shipping/handling
Hall Effect Half Throttle Control and 4 wire cable
harness 4 pin connector, Red (4.3 Volts), Green (or blue
- Speed Adjusting Signal), Black (Ground), if 4th wire - White wire (or
Yellow to Speed or Power Indicator of control box). Insert blades into existing connector or splice for
quick repair. 7/8 inch standard handlebar mount. Used on E500, MX350, Pocket mod Bistro/Bella, Razor Dirt Quad, Razor Mini-Chopper 300, Razor Pocket Mod, Razor Rebellion Mini-Chopper, Razor Pocket Rocket (PR200), Razor Sport Mod
4 Pin, 4 Wire, Not compatible with Razor 5-wire throttles.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Pedal Throttle Control Assembly For Scooters $29.95
plus shipping/handling
Hall Effect Throttle Control and 40 inch 3 wire cable
harness (terminating in bare wire), Red (4.3 Volts), Green (or blue
- Speed Adjusting Signal), Black (Ground). Splice for
quick repair. Used in electric go carts.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Medal Pedal Throttle Control Assembly For Scooters $39.95
plus shipping/handling
Spring loaded Hall Effect Throttle Control and 40 inch 3 wire cable
harness (terminating in bare wire), Red (4.3 Volts), Green (or blue
- Speed Adjusting Signal), Black (Ground). Splice for
quick repair. Used in Chinese electric go carts.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Throttle Switch Assembly with 42 inch two wire harness For Many 100 watt Scooters $19.95
plus shipping/handling
Common finger 'Go Switch throttle' that fits 7/8"
Diameter Handlebar.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Turn Signals built into Mirror - $29.95
- Full size scooter mirror set similar to Vento Phantom style. Turn signals built into front of mirror. Bolt Size: M8 x 1.25. No returns or exchange possible.
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Front Orange Turn Signal Lens Set
(2), for X360 - $25.95
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Front Yellow Turn Signal Lens
Set (2), for X360 - $21.95
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Turn Signal, rear set of two, for
X360 - $25.95
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
Tail and Stop Light Assembly for X360
$25.95
READ IMPORTANT INFORMATION ON PLACING USA AND INTERNATIONAL ORDERS HERE
International Customers: Save Time and Pay Your Shipping Fee Here with the Order
ADD $1 SHIPPING IF ORDER TOTAL IS LESS THAN $10
PICTURES OF REPLACEMENT PARTS MAY VARY PRIOR TO UPDATES. PARTS ARE PROVIDED IN AS-IS CONDITION WITH NO REGARD TO SLIGHT COSMETIC IMPERFECTIONS DUE TO STORAGE OR HANDLING, AND PRODUCTION RUNS MAY SLIGHTLY ALTER THE APPEARANCE OF THE SAME PART FROM TIME TO TIME MAKING SLIGHT DIFFERENCES FOR MATCHING OF SEVERAL ITEMS IN AN ORDER (WHENEVER POSSIBLE WE MATCH AS CLOSELY AS POSSIBLE FOR ORDERS WHERE CUSTOMERS REQUEST THIS). ALL PARTS ARE INSPECTED AND TESTED AS POSSIBLE FOR QUALITY CONTROL PRIOR TO PACKAGING AND SHIPMENT OF CUSTOMER ORDERS. ALL SALES ARE FINAL WITH THE EXCEPTION OF NON-ELECTRICAL ITEM EXCHANGES FOLLOWING OUR TERMS OF SALE ORDER POLICIES FOR THE ORDERING OF INCORRECT PARTS. CUSTOMERS SHOULD ALWAYS TAKE ADVANTAGE OF OUR 24/7 EMAIL AND OTHER COMMUNCIATIONS FOR HELP PRIOR TO PLACING ORDERS, IF NEEDED. USA STANDARD SHIPPING IS INCLUDED IN THE PRICE OF PARTS ONCE ADDED TO THE SHOPPING CART THAT ALSO REPRESENTS THE HANDLING FEE FOR INTERNATIONAL ORDERS. INTERNATIONAL SHIPPING IS SEPARATE FOR EACH ORDER BASED ON INFORMATION PROVIDED ON OUR 'HOW TO PLACE AN ORDER' PAGE USING THE LINK IN THE ITEM DESCRIPTION. USA HANDLING IS ADDED TO EACH ORDER DURING CHECK-OUT TO ADJUST SHIPPING AND PROCESSING OF EACH USA ORDER. PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE AND CUSTOMER WILL BE ADVISED IN THAT EVENT.
SCOOTER ELECTRICAL
